How to Make a Roman Blind

#RomanBlind #Howto #DIY #Homecraft
Share on FacebookTweet about this on TwitterPin on PinterestShare on Google+Share on StumbleUpon

Sewing Machine Basics by Jane Bolsover

This blind will brighten up any room instantly, so grab your sewing machine and have a go with this step-by-step . . .

All imagery and text courtesy of Sewing Machine Basics by Jane Bolsover published by CICO Books

How to Make a Roman Blind

Skill level: Intermediate

You will need

For the blind –

  • Cotton or linen plains and prints
  • Matching thread
  •  Sew-and-stick hook-and-loop tape fastener cut to finished width of blind
  •  Six millimetres wooden dowels cut to finished width of blind minus 11 centimetres; allow one per fold of blind
  •  Roman blind tape; for quantity, multiply width of blind by number of folds
  •  Fine Roman blind cord; for quantity, multiply length of blind by seven
  •  15 small plastic rings
  •  2.5 centimetre wide wooden lath cut to width of blind minus 1.5 centimetres
  • Cord pull

For the blind support and fixing –

  • 2.5 x 5-centimetre timber batten, cut to width of finished blind
  • Medium brass screw eyes
  • Cleat to secure cords
  • Screws
  • Staple gun

How to make

1.Measure your window and calculate your cut blind size, then cut out your fabric. If you need to join fabric widths, use French seams, or Mock French seams if you need to match any pattern repeats. Press a 2.5 centimetre double-turned hem down each side of the blind. Pin, baste (tack), and machine stitch in place.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

2. Press over two centimetres to the wrong side along the base edge, then press over a further four centimetres to form a double-turned hem. Pin, baste (tack), and machine stitch in place.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

3. Press over 2.5 centimetres to the wrong side along the top edge of the blind. Trim the hem allowance down to 1.5 centimetres and baste (tack) in place. Attach the fluffy side of the hook-and-loop tape to the wrong side of the blind at the top edge, enclosing the raw edge.

 How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

4. To calculate and mark the spacing for the Roman blind tapes. Cut lengths of tape to fit the width of your blind. Place the tapes on the blind, positioning the top edge of each piece along the chalked lines. Pin, baste (tack), and machine stitch the tapes in place along the top edge only, starting and finishing two centimetre in from each end of the tape and reverse stitching to secure.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

5. Insert the wooden lath through the base hem channel and slip stitch the open ends closed. Insert the dowels through the casings in the tapes. To neaten the raw ends, fold over a double-turned hem at each end and slip hem to secure.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

6.Lay the blind wrong side up on a flat surface. Sew a plastic ring to the loose edge of each Roman blind tape, placing them five centimetres in from the side edges of the blind. Sew a third ring to each tape at the center point. Knot a length of cord to each of the bottom rings and thread the cords vertically up through the rest of the rings.

 How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

7. Using the hook-and-loop tape, attach your blind to the blind support. Working from the wrong side of the blind, thread the cords up through the screw eyes directly above, then pass them across to the operating end, making sure that all cords go through the fourth screw eye.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

8. Attach the cord pull to the loose ends of your cords and screw the cleat to the side of the window frame. To raise your blind, pull on the cord pull and secure the cords around the cleat in a figure of eight.

How to make a unlined roman blind from Sewing machine basics by Jane Bolsover

The finished blind

CB401_Diag_11,10 CB401_Diag_11,12Roman blind from Sewing machine basics by Jane Bolsover

 Hints and Tips

For more information on how to measure your window for a Roman blind, how to position the blind tapes and make you own blind support, as well as many other useful hints and tips, make sure to check out the Sewing machine Basics book by Jane Bolsover for more details.

 Shop Knit and Stitch >

Share on FacebookTweet about this on TwitterPin on PinterestShare on Google+Share on StumbleUpon

Hobbycraft Inspirational Content Marketing Assistant, I'm in love with all things craft, vintage and floral. I spend my spare time visiting craft fairs in the south on the look out for something that's a little bit different. When not out exploring by foot I'm on my bike riding around the country side or down by the beach.

Leave a comment & join the conversation